Nuvi 760 a defragmentace

[morganzd]

jj, je to srandovní
Mapy: Atlas Czech NT 7 (nuvi), CN NT 2009 CZ+SK+A+HR+sever I (karta), Topo Czech 2.0 Pro (karta)
mp3: nic
jpg: nic
poi: nevím, doplním (nuvi jsem teď půjčil kolegovi, nemám ji doma)
+ uložené trasy (Brno - Umag, Brno - Zadov)

Když jsem tam měl původní kompletní CN NT (nevím verzi), mapa měla cca 1.3G. Teď tam je balíček uvedených map a soubor má cca 400M. Na četnost "dlouhých starů" ani na jejich délku to nemá vliv.
Teď jsem si ještě uvědomil, že na jedné z servisních obrazovek (nebo co to je zač) mi hlásí nějaké chyby v kontrole (failed check). Teď nedám z hlavy co to bylo zač, ale v názvu bylo tuším cosi jako "...cyclops..." a bylo to pro různé státy (cca 7ks). Myslím, že se jedná o nějakou obdobu POI??? Upozornění na radary apod.???

[Path]

Cyclops jsou ukázkové POI, zde o nic nejde. Zkoušel jste také přesunout Evropu a TC 2 Pro z karty do nuvi? Zkuste to bez karty a uvidíme, jak se bude čas zavádění lišit.

[morganzd]

Vracím se po řádné odmlce...
Zkoušel jsem už snad vše, i jen jednu mapu umístěnu v gps a bez karty. Dá se říct, že na 99%, pokud naplánuji trasu, provede se výpočet, uložím, vypnu navi (NEspustím simulaci), zapnu navi... a nápis Loading maps se neskutečně dlouho tlemí z displaye. Pak, když se napíše Načítání map jde již vše jak má.
Z.

[Tragedie_v_JZD]

Jo, to je znama chyba 760ek...

[nanaa]

Ano, to je pravda. Nicméně by mne zajímalo, zda tento problém může řešit garmin aktualizacví firmware. Pokud to nejde, pak je to poměrně velký handicap.

[kotivs]

Mám ten istí problém a už som skúšal všetko možné ale zbytočne. Mám ten dojem že v Garmine na to kašlú a viac sa venujú novším navigáciam.

[Path]

Určitě by to upraveným firmwarem vyřešit šlo. Ale to se musíte obrátit přímo na podporu Garmin. První pravidlo: Čím více uživatelů se ozve, tím větší šance na úspěch. Druhé pravidlo: Čím stručnější e-mail se Garminu napíše, tím je větší šance, že jej někdo dočte do konce. Třetí pravidlo: Opakovat se.

Je to smutné, ale je to tak.

[Hopkirk]

...Třetí pravidlo: Opakovat se.

Panove, kdo to umite, napiste sem prosim vzor textu a ostatni to tam muzou vesele meilovat (treba s drobnymi zmenami, aby z toho neudelali spam).

[morganzd]

Moje angličtina je mizerná, nicméně přikládám řetězec mailů, které jsme si vyměnili se supportem, než jsem to vzdal...
Čtěte, prosím, od konce.


Dear Matthew,

I went through history of our correspondence and I couldn't find any place where I told you that there is nothing actually wrong with my unit.
I only described how the support look like ("not know what to advice, everything is looking OK and working fine").
Sorry if I am not too polite, but this is my feeling.
If the start time above 1 minute is OK and it is caused due to loading lot of map data, WHY my unit sometimes starts in 20 seconds with the same configuration, map, custom data etc.???
The only thing I would like to know now is: what the defregmentation in nuvi do and when it is performed?
Because the Defrag Count is always incremented when nuvi starts up long time.

Kind regards
Zdenek


>
>Dear Zdenek Pavlus,
>
>Thank you for contacting Garmin Europe.
>I apologise that you do not find my suggestions useful, or that you find
>them "funny", however as you have pointed out, there is nothing actually
>wrong with your unit. You have told me it is working fine. The standard
>time for a nuvi 760 is not 20 seconds, please bare in mind the software
>and hardware that has to load at the start, also the fact there is full
>European mapping installed, this is a lot of data it has to read
>through.
>If there is anything else I can help you with then please let me know.
>Alternatively you can search for a solution here: http://www.garmin.com/support
>
>Kind regards
>Matthew Morley
>Garmin ( Europe ) Ltd



>Dear "support",
>
>it is very funny to see that when you do not know what to advice,
>everything is looking OK and working fine...
>Can you imagine the situation when somebody wants to go somewhere and
>must stay and wait minute or two until GPS is started up? Standard time
>is about 20 seconds!
>I cannot believe that this is correct behaviour and that you personally
>would be happy with it.
>Thanks for your support. Most likely I will send my garmin to repair.
>
>Zdenek
>

>>
>>Dear Zdenek Pavlus,
>>
>>Thank you for contacting Garmin Europe.
>>OK, well your unit doesn't sound like it isn't working, so there isn't
>>much more I can do I'm afraid. it has been reported that doing the
>>software update / master reset can improve the time it takes for the
>>unit to load, but over a minute isn't anything to drastic, so I'm sure
>>it is working fine. I hope this covers everything you require.
>>If there is anything else I can help you with then please let me know.
>>Alternatively you can search for a solution here: http://www.garmin.com/support
>>
>>Kind regards
>>Matthew Morley
>>Garmin ( Europe ) Ltd



>>Dear Matthew,
>>
>>Thank for your advices but I already have updated software and also I
>>have
>>performed master reset in the way you described below.
>>Unfortunately this didn't solve my problem.
>>
>>Zdenek
>>
>>
>>
>>Dear Zdenek Pavlus,
>>
>>Thank you for contacting Garmin Europe.
>>I am happy to help with your query. I would strongly recommend against
>>entering the pre boot mode unless advised to by a Product support
>>associate as it will be very easy to delete something that you
>>shouldn't, and therefore void the warranty. If you are finding the unit
>>is taking longer to load up, in my opinion the best way to solve this
>>would be with a software update and master reset. To carry out a
>>software update, you will need to connect your Garmin device and use
>web
>>updater, for which I have included a guide. Once the software update is
>>complete, you will need to do a master reset (this will take 45
>minutes,
>>this may delete any favourites or saved locations you have on your
>>unit), this can be done by following these instructions.
>>
>>1. Turn off the unit.
>>2. Press and hold the bottom right hand corner of the touch screen.
>>3. Turn on the unit, keeping finger on the bottom right hand corner of
>>the screen.
>>4. The following message will appear ?Do you want to clear all user
>>data?? select yes.
>>5. Follow the next instructions.
>>6. Leave the unit, in clear view of the sky (outside, in a glass roofed
>>conservatory, by a window or on a car dash board), not moving for 45
>>minutes, this is to allow the system to fully read and understand the
>>gps signal.
>>
>>If there is anything else I can help you with then please let me know.
>>Alternatively you can search for a solution here:
>>http://www.garmin.com/support
>>
>>Kind regards
>>Matthew Morley
>>Garmin ( Europe ) Ltd



>>Subject:
>>Defragmentation
>>Message Body:
>>Can you provide me with information what does nuvi 760 defragment?
>There
>>are values of Defrag Count and Defrag Date on diagnostic screen "Nonvol
>>Info". I experienced very very long gps starting time after which I
>>noticed that Defrag Count was incremented. This long starting is quite
>>often and it is annoying me, because it takes about 1 minute and more.
>>Thanks for advice, Zdenek Pavlus

[Path]

Pěkné, nemohl byste ten e-mail nějak osekat? Zabavit ho těch zbytečných textů?